outline drawing hybrid ic M57147AU-01 ipm power suppl y unit block diagram description the M57147AU-01 is an insulated dc-dc converter de- signed to drive the ipm. 6 outputs can obtain from an input of 140 ~ 380vdc. the terminals between inputs and outputs, and each outputs are insulated. fea tures ? input ................................................... 140 ~ 380vdc ? output ................................................ +15v , 50max3 +15v , 150max1 +12v , 400max1 +5v , 300max1 ? electrical isolation (between input and outputs) ........................................................... 1500v rms 1minute ? electrical isolation (between each outputs) ........................................................... 1500v rms 1minute applica tion power supply for ipm drive dimensions: mm 18 1 19 36 M57147AU-01 xxxx lot no pin no 82max 50 0.7 80.35 0.35 0.2 2.54 0.55 0.1 2.54 17=43 33 max 1.6 4.5 1.5 (3.41) control circuit vo1+ vo2+ vo3+ vo4+ 18 vo6+ vo5+ vin+ vin ? 17 16 12 11 10 vo5,6 vo4 ? vo3 ? vo2 ? vo1 ? 19 20 24 25 29 30 35 1 2 3 5 4 34
hybrid ic M57147AU-01 ipm power supp l y unit maximum ra tings (t a = 25 c, unless otherwise noted) v v v v ma c c w v rms v rms 380 50 150 400 300 ? 10 ~ 70 ? 20 ~ 85 *10.8 1500 1500 ratings symbol parameter conditions unit 140 14 14 14 14 11 4.75 ? ? ? ? ? ? ? 15 15 15 15 12 5.0 0.3 0.3 0.3 0.3 0.2 0.1 380 16 16 16 16 14 5.25 0.5 0.5 0.5 0.5 0.5 0.2 symbol unit parameter t est conditions limits min. t yp. max. input voltage output current operating temperature storage temperature t otal output power electrical isolation between input and outputs electrical isolation between each outputs vi n i l t opr t stg po v iso1 v iso2 ? v o1, v o2, v o 3 vo 4 vo 5 vo 6 no condensation no condensation ? sine wave voltage, 60hz, 1 minutes sine wave voltage, 60hz, 1 minutes recommended range io1 = 5 ~ 50ma, io2 = io3 = 5ma, io4 = 25ma io5 = 200ma, io6 = 200ma io2 = 5 ~ 50ma, io1 = io3 = 5ma, io4 = 25ma io5 = 200ma, io6 = 200ma io3 = 5 ~ 50ma, io1 = io2 = 5ma, io4= 25ma io5 = 200ma, io6 = 200ma io4 = 25 ~ 150ma, io1 = io2 = io3 = 5ma io5 = 200ma, io6 = 200ma io5 = 30 ~ 400ma, io1 = io2 = io3 = 5ma, io4 = 25ma io6 = 200ma io6 = 50 ~ 300ma, io1 = io2 = io3 = 5ma, io4 = 25ma io5 = 200ma v o1 voltage change io1 = io2 = io3 = 50ma, io4 =150ma, io5 = 400ma, io6 = 300ma v o2 voltage change io1 = io2 = io3 = 50ma, io4 =150ma, io5 = 400ma, io6 = 300ma v o3 voltage change io1 = io2 = io3 = 50ma, io4 =150ma, io5 = 400ma, io6 = 300ma v o4 voltage change io1 = io2 = io3 = 50ma, io4 =150ma, io5 = 400ma, io6 = 300ma v o5 voltage change io1 = io2 = io3 = 50ma, io4 =150ma, io5 = 400ma, io6 = 300ma v o6 voltage change io1 = io2 = io3 = 50ma, io4 =150ma, io5 = 400ma, io6 = 300ma vi n vo 1 vo 2 vo 3 vo 4 vo 5 vo 6 reg-i input voltage output voltage line regulation electrical characteristics (v in= 140 ~ 380v , t a = 25 c, unless otherwise noted) *refer to output power vs.input v oltage charactreristics
hybrid ic M57147AU-01 ipm power suppl y unit v % ? ? ? ? ? ? 70 0.4 0.4 0.4 0.5 1.5 0.1 77 1.0 1.0 1.0 1.0 1.8 0.2 ? symbol unit parameter t est conditions limits min. t yp. max. v o1 voltage change io1 = 5 ~ 50ma, io2 = io3 = 50ma, io4 = 150ma, io5 = 400ma, io6 = 300ma, v in = 300v v o2 voltage change io2 = 5 ~ 50ma, io1 = io3 = 50ma, io4 = 150ma, io5 = 400ma, io6 = 300ma, v in = 300v v o3 voltage change io3 = 5 ~ 50ma, io1 = io2 = 50ma, io4 = 150ma, io5 = 400ma, io6 = 300ma, v in = 300v v o4 voltage change io4 = 25 ~ 150ma, io1 = io2 = io3 = 50ma,, io5 = 400ma, io6 = 300ma, v in = 300v v o5 voltage change io5 = 30 ~ 400ma, io1 = io2 = io3 =50ma, io4 =150ma, io6 = 300ma, v in = 300v v o6 voltage change io6 = 50 ~ 300ma, io1 = io2 = io3 = 50ma, io4 =150ma, io5 = 400ma, v in = 300v v in = 300v , po = 10.8w reg-l load regulation ef ficiency electrical characteristics (v in= 140 ~ 380v , t a = 25 c, unless otherwise noted)
typical characteristics available ipm examples pm100cv a060 pm10csj060 pm100csa060 pm50rsa060 pm50rsk060 pm15ctm060 pm150cv a060 pm15csj060 pm150csa060 pm75rsa060 pm75rsk060 pm15ctm060-3 pm200cv a060 pm20csj060 pm200csa060 pm100rsa060 pm20ctm060 pm30csj060 pm150rsa060 pm30ctj060 pm20ctm060-3 pm50ctk060 pm30ctj060-3 pm75r v a060 pm30rsf060 pm75ctk060 ac200~240v + v in + v up1 v upc v vp1 v wp1 u p v vpc v wpc v p w p u n v n w n ipm f 0 v n1 ex. pm15/20ct m060(-3) v o 1+ v o 1 ? v o 2 ? v o 2+ v o 3+ v o 5+ v o 6+ v o 5, v v o 4+ M57147AU-01 v o 3 ? v o 4 ? v in ? load + + + + load hybrid ic M57147AU-01 ipm power suppl y unit
ihybrid ic m5714 7 au - 01 ipm power supply unit for safety using great detail and careful attention are given to the production activity of hics, such as the development, the quality of production , and in it ? s reliability. however the reliability of hics depends not only on their own factors but also in their condition of usage. when handling hics, please note the following cautions. cautions packing carrying storage extended st orage maximum ratings polarity the materials used in packing hics can only withstand normal external conditions. when exposed to outside shocks, rain and certain environmental contaminators, the packing materials will deteriorates. please take care in handling. 1) don ? t stack boxes too high. avoid placing heavy materials on boxes. 2) boxes must be positioned correctly during transportation to avoid breakage. 3) don't throw or drop boxes. 4) keep boxes dry. avoid rain or snow. 5) minimal vibration and shock during transportation is desirable. when storing hics, please observe the following notices or possible deterioration of their electrical characteristics, risk of solder ability , and external damage may occur. 1) devices must be stored where fluctuation of temper ature and humidity is minimal, and must not be exposed to direct sunlight. store at the normal temperature of 5 to 30 degrees celsius with humidity at 40 to 60%. 2) avoid locations where corrosive gasses are generated or where much dust accumulates. 3) storage c ases must be static proof. 4) avoid putting weight on boxes. when extended storage is necessary, hics must be kept non - processed. when using hics which have been stored for more than one year or under severe conditions, be sure to check that the exterior is free from flaw and other damages. to prevent any electrical damages, use hics within the maximum ratings. the temperature , current, voltage, etc. must not exceed these conditions. to protect hics from destruction and deterioration due to wrong inserti on, make sure of polarity in inserting leads into the board holes, conforming to the external view for the terminal arrangement.
ihybrid ic m5714 7 au - 01 ipm power supply unit marketing division, marketing planning department 6 - 41 tsukuba, isahaya, nagasaki, 854 - 0 065 japan keep safety first in your circuit designs! isahaya electronics corporation puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. trouble with semiconductors may lead to personal injury, fire or property damage. remember to give due consideration to safety when making your circuit designs, with appropriate measures such as ( 1) placement of substitutive, auxiliary, ( 2) use of non - farmable material or ( 3) prevention against any malfunction or mishap. notes r egarding these materials these materials are intended as a reference to our customers in the selection of the isahaya products best suited to the customer?s application; they don't convey any license under any intellectual property rights, or any other ri ghts, belonging isahaya or third party. isahaya electronics corporation assumes no responsibility for any damage, or infringement of any third party's rights , originating in the use of any product data, diagrams, charts or circuit application example s contained in these materials. all information contained in these materials, including product data, diagrams and charts, represent information on products at the time of publication of these materials, and are subject to change by isahaya electroni cs corporation without notice due to product improvements or other reasons. it is therefore recommended that customers contact isahaya electronics corporation or an authorized isahaya products distributor for the latest product information before purchasing product listed herein. isahaya electronics corporation products are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. please contact isahaya elec tronics corporation or an authorized isahaya products distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea re peater use. the prior written approval of isahaya electronics corporation is necessary to reprint or reproduce in whole or in part these materials. if these products or technologies are subject to the japanese export control restrictions, they must be exported under a license from the japanese government and cannot be imported into a country other than the approved destination. any diversion or re - export contrary to the export control laws and regulations of japan and/or the country of destina tion is prohibited. please contact isahaya electronics corporation or authorized isahaya products distributor for further details on these materials or the products contained therein. nov.2002
|
